Product Description
50gm Art Clay Copper Clay, a gorgeous warm-coloured and strong clay, with an extremely simple firing schedule.
Art Clay Copper only requires a 30-minute kiln firing time, and you don't need to use any activated carbon or firing pans - you can even fire it with a torch! It is an incredibly reliable clay, and the clay we recommend wholeheartedly to anyone new to base metal clay.
You shape and work with Art Clay Copper just like normal silver clay. You can mould it, press textures into it, stick dry pieces together, set stones in it; exactly as you would when working with silver clay. Art Clay Copper has a shrinkage rate of 8-10% which is similar to Art Clay Silvers 8-9%. Make sure any tools you use are clean of silver clay, as this would contaminate your copper, creating an alloy which doesn't take to firing very well at all. Use separate files and abrasive papers/sponges, as these are almost impossible to clean.
HOW TO USE
Kiln firing:
Put the dried clay on shelf paper on a kiln shelf, as the copper can stick to the shelf slightly. Place in a hot kiln and fire at 970C for at least 30 minutes. When finished, don't let the kiln cool down. You need to quench the piece immediately from hot. Keep a steel bowl just under the kiln door, and as soon as you open the door, tip the kiln shelf over so the piece/pieces drop into the water. Every second the piece is exposed to the cooler air, it will oxidise, which will damage the piece. The quenching will allow most of the oxidised layer which occurs during firing to peel off.
We also highly recommend firing under a thin layer of carbon - this makes the quenching a little less stressful, as the carbon layer will protect the copper and you can take a little longer moving it from the hot kiln to the quenching bowl. We literally poor a little carbon on top of the piece straight onto the shelf, so the piece is just covered with a couple of millimetres of carbon. This gets poured into the quenching bowl with the piece, but can then be sieved out, dried, and used again.
Torch firing:
You can torch fire smaller Art Clay copper pieces, keep them under 35gm, and ideally not much bigger than a 50p coin as anything bigger is impossible to keep evenly heated for the whole firing.
Place the piece on a firing brick and heat until cherry red (much hotter than silver needs) for at least 5-7 minutes, depending on size. Copper needs to be quenched immediately once you move the flame from it. This stops it from getting too much fire scale/oxidisation. Keep a bowl of water close to your firing brick and keep it so it is level or under the edge of the fibre brick; using long tweezers or tongs, either push the piece towards the water following it with the flame until it hits the water, or move the flame away and quickly pick up/push the piece into the water.
Storing Art Clay Copper:
The surface of Art Clay Copper will naturally start oxidising, and the colour will darken over time if left in the air. If you do get a darkened surface on your unfired clay - scrape most of the layer off, smoosh in any small dark pieces into the remaining clay. To avoid oxidisation of unused clay, wrap it in layers of cling film tightly, then place in a grip seal bag or airtight container. Our Art Clay Storage Pot is great for keeping your clay fresh and workable. Keep the clay indoors at a moderate room temp and out of direct sunlight.
Did you know we stock embeddable copper findings? 'Embeddable' means you can add them to your clay in the wet stage and fire all at once.
Click here to see our full range of embeddable findings.
Product Videos
Videos Hide Videos Show Videos
Custom Field
Product Reviews
32 Reviews
-
Can I fire on gas stove too?
I fire my silver on my gas hob and it works prefectly for me...can I do the same with copper? (I have a torch too, but just wondered) x Hi there, It's not recommended to gas hob fire Art Clay Copper. With gas hob firing, it's a lot harder to control the temperature. This isn't a problem with silver, and it doesn't have the complications of fire scale that copper does. Torch firing this works great though, and is super easy. Please do give us a call if you need any more advice on this, our number is 01929 481541. The Metal Clay Team
-
Easier then expected
I'm new to this art clay. Worked with normal air dry clay, but was abit warry of this. Got some silver clay but not alot so brought copper clay to perfect before using the silver (as expensive!). Was surprised at how good it was. Still yet to fire my piece (next couple of days), so hopefully will impress even more. So pleased, just placed order for some more.
-
Easy to Use
this is the first time I have used it; but its so easy to work with and great results; just firing with a torch
-
1st copper project
Just started last night but so far so good wetter than the silver clay but than can be a bonus for refining errors
-
Really easy to work with.
I have never used copper clay before so I can't say how this compares. I am however a compleat beginner with metal clay (I have only used silver clay once before) but this was very easy to work with. You need to research the dos and donts first, but I had no problems once I braved opening the pack!
-
Good clay with improved quality.
This clay is softer and it has a longer drying out time than previous, therefore you can correct any mistakes and try again.
-
Big improvement
I have been using copper clay for a while now, and loved it. But this new, improved formula is fantastic, with a creamy texture and a long work time without drying out at the edges. Firescale is not a problem with quick quenching, and I get the stubborn bits off by immersing the cooled pieces in a solution of warm water, vinegar, and salt for five to ten minutes.
-
As easy as it says.
Just tried this and I'm very happy with the results. I was skeptical but it really is a lovely result. Shiny and lovely warm colour. Remember to have a big pot of water nearby to quickly quench in and you'll find 90% of the black oxidization jumps right off! After a little bit of brushing it's ready to go.
